[1] Acar, M., Balikci, E., Kuskun, T., Kasal, A. and Ziya Erdil, Y., 2023. Shear Force Capacities of H-Type Furniture Joints Constructed of Various Heat-Treated Wood Species. Drvna industrija, 74(1), pp.33-42.
[2] Dalvand, M., Ebrahimi, G., Haftkhani, A. R., and Maleki, S., 2013. Analysis of factors affecting diagonal tension and compression capacity of corner joints in furniture frames fabricated with dovetail key. Journal of Forestry Research, 24(1): 155-168.
[3] Smardzewski, J., Rzepa, B., and Kıliç, H., 2016. Mechanical properties of externally invisible furniture joints made of wood-based composites. BioResources, 11(1): 1224-1239.
[4] Smardzewski, J., 2002. Strength of profile-adhesive joints. Wood Science and Technology, 36(2), pp.173-183.
[5] Džinčić, I. and Skakić, D., 2012. Influence of type of fit on strength and deformation of oval tenon-mortise joint. Wood Research, 57(3), pp.469-478.
[6] Džinčić, I. and Živanić, D., 2014. The influence of fit on the distribution of glue in oval tenon/mortise joint. Wood Research, 59(2), pp.297-302.
[7] Kasal, A., Erdil, Y.Z., Demirci, S. and Eckelman, C.A., 2013. Shear force capacity of various doweled frame type furniture joints. Kastamonu University Journal of Forestry Faculty, 13(1), pp.60-71.
[8] Prekrat, S. and Smardzewski, J., 2010. Effect of glueline shape on strength of mortise and tenon joint. Drvna industrija, 61(4), pp.223-228.
[9] Hajdarević, S. and Martinović, S., 2015. The effect of dowel spacing on the stress and strain of case-type furniture corner joint. Annals of DAAAM & Proceedings, 26(1).
[10] Dalvand, M., Ebrahimi, G., Tajvidi, M. and Layeghi, M., 2014. Bending moment resistance of dowel corner joints in case-type furniture under diagonal compression load. Journal of Forestry Research, 25, pp.981-984.
[11] Hu, W., Luo, M., Liu, Y., Xu, W. and Konukcu, A.C., 2023. Experimental and numerical studies on the mechanical properties and behaviors of a novel wood dowel reinforced dovetail joint. Engineering Failure Analysis, 152, p.107440.
[12] Uysal, M., Tasdemir, C. and Memis, D., 2023. Effect of Epoxy Resin Reinforcement on Screw Withdrawal Strength of Fiberboard and Particleboard Used in the Furniture Industry. Drvna industrija, 74(4), pp.491-500.
[13] Gašparík, M., Karami, E., Kytka, T., Das, S. and Houska, T., 2023. The influence of freezing and heating on the nail withdrawal capacity of Norway spruce and European larch wood. European Journal of Wood and Wood Products, 81(2), pp.387-398.
[14] Hoelz, K., Doerner, P.T., Hohlweg, J. and Matthiesen, S., 2022. Influence of thread parameters on the withdrawal capacity of wood screws to optimize the thread geometry. European Journal of Wood and Wood Products, 80(3), pp.529-540.
[15] Dalvand, M., Pourtahmasi, K., Ebrahimi, G., 2021. 'Numerical modeling of screw connector performance in LVL under shear loading', Forest and Wood Products, 74(3), pp. 357-369. 10.22059/jfwp.2021.320436.1156
[16] Maleki, S., Faezipour, M., Ebrahimi, G. Layeghi, M., 2012. Investigation on bending moment resistance of l-shaped screwed corner joints constructed of plywood members. iranian journal of wood and paper science research, 27(4 (41)) , 731-742.
[17] Örs, Y., Özen, R. and Doğanay, S., 1998. Screw Holding Ability (Sterength) of Wood Materials Used in Furniture Manufacture. Turkish Journal of Agriculture and Forestry, 22(1), pp.29-34.
[18] Standard test methods for Mechanical fasteners in wood, Annual Book of ASTM Standard, D 1761–88, 2008.
)