@article { author = {Ghahri, Saman and K.Najafi, Saeid}, title = {A Study on Creep Behavior of Wood Flour- Recycled Polypropylene Composite}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {3}, number = {2}, pages = {1-12}, year = {2013}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {The creep behavior of wood flour- recycled polypropylene composites (with and without compatibilizer) has been evaluated in this study. For this purpose, virgin polypropylene (PP) was thermo-mechanically degraded by five times of extrusion under controlled conditions in a twin-screw extruder at a rotor speed of 100 rpm and at temperature of 1900C. The virgin and recycled polypropylene were mixed with the wood flour (50/50% W/W) as well as the compatibilizer (0, 2% W/W) by a counter-rotating twin-screw extruder to manufacture the wood flour-PP composites (WPCs) samples. The nominal cross section of the manufactured composites was 70×10 mm2. Short term flexural creep test at 30% of ultimate bending load was performed by using flexural creep equipment. The total time to complete every test was 120 min (60 min creep and 60 min recovery). Results revealed that recycling of the PP reduced the creep resistance in composites containing recycled polypropylene. Also results have shown that with the presence of compatibilizer (MAPP) creep deflection, creep factor and relative creep decrease and creep modulus increase. The composites containing virgin PP and MAPP exhibited higher creep resistance than those containing recycled PP.}, keywords = {Recycling of polypropylene,Creep,Wood flour- Recycled,polypropylene composite,Compatibilizer}, title_fa = {بررسی رفتار خزش چندسازه آرد چوب- پلی‌پروپیلن بازیافتی}, abstract_fa = {در این پژوهش، رفتار خزش چندسازه آرد چوب- پلی‌پروپیلن بازیافتی (با سازگار کننده و بدون آن) مورد ارزیابی قرار گرفت. برای این منظور، پنج مرحله تخریب گرمایی (ترمو)مکانیکی مصنوعی پلی‌پروپیلن با دستگاه تزریق چسب (اکسترودر) دو مارپیچ در شرایط کنترل شده با شتاب rpm  100 و دمای ºC 190 صورت گرفت. پلی‌پروپیلن دست اول (بکر و بازیافتی) و آرد چوب با نسبت 50 درصد وزنی در بود و نبود سازگار کننده (MAPP) با دستگاه تزریق چسب دو مارپیچ مخلوط شده و در نهایت باریکه‌هایی با سطح مقطع mm 10 (ضخامت) در mm 70 (پهنا) ساخته شدند. آزمون خزش خمشی کوتاه مدت در 120 دقیقه (60 دقیقه خزش و 60 دقیقه بازگشت) انجام شده است. میزان بارگذاری در آزمون خزش بر پایه 30 درصد از بار شکست نمونه‌ها (حاصل از آزمون خمش ایستا) تعیین شد. نتایج به دست آمده از این تحقیق نشان داد که با افزایش بارهای بازیافت پلی‌پروپیلن مقاومت به خزش در چندسازه ساخته شده از پلی‌پروپیلن بازیافتی و آرد چوب کاهش می یابد. همچنین نتایج بررسی های اثرگذاری سازگارکننده بر رفتار خزشی نشان داد که در بود سازگار کننده MAPP تغییر شکل خزشی، ضریب خزش و خزش نسبی کاهش و مدول خزش در چندسازه‌های مورد بررسی افزایش می‌یابد.}, keywords_fa = {بازیافت پلی‌پروپیلن,خزش,چندسازه آرد چوب,پلی‌پروپیلن دست اول (بکر),سازگار کننده}, url = {https://www.ijwp.ir/article_11472.html}, eprint = {https://www.ijwp.ir/article_11472_ca44e205ea5d8fc2b49b482078d3d4cc.pdf} } @article { author = {Mohammadzadeh, Kamel and Resalati, Hossein}, title = {The Survey of Chemical Paper Pulp Properties Produced from Rice Straw Based on Formaldehyde Sulfide Method.}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {3}, number = {2}, pages = {13-23}, year = {2013}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {The aim of this study was to evaluate the effect of formaldehyde addition to Sodium Sulfide cooking liquor for chemical Pulp Production from rice straw. Rice straw (oryza sativa) was collected from the rice field of Salmanshahr and was carried to the laboratory of wood and paper in Gorgan University. Digestion conditions of pulp included cooking temperature of 160 °C, digestion times of 30, 60 and 90 min and useing chemical (16, 18 and, 20% Sodium sulfite and 4 and 6% formaldehyde) based on oven dry dosages weight of raw material. Four different treatments, at a Kappa number ranges of 12 - 14 were selected from each pulp In order to evaluate the effect of formaldehyde added based on Kappa number and pulp yield relations. Hand sheets with grammage of 60 g/m2 were prepared from each of pulp samples and their properties were measured using the related Tappi standard. The results indicated that the addetion of formaldehyde in sulfite liquor increased the pulp yield at the same Kappa number, accelerated delignification rate and improved delignification selectiving as well as improving the mechanical properties of paper}, keywords = {: Rice straw,Paper Pulp,Sulfide sodium,Formaldehyde,Mechanical properties}, title_fa = {ررسی ویژگی‌های خمیرکاغذ شیمیایی تهیه شده از کاه برنج به روش سولفیت فرمالدهید}, abstract_fa = {این تحقیق با هدف بررسیاثرگذاری افزودن فرمالدهید به مایع (لیکور) سولفیت برای تهیه خمیرکاغذ از کاه برنج انجام شد. کاه برنج (رقم طارم) از شالیزارهای سلمانشهر تهیه شدهو به آزمایشگاه صنایع چوب کاغذ دانشگاه گرگان برای انجام آزمایش ها منتقل شده است.شرایطپخت برای تولید خمیرکاغذ شامل دمای پخت 160 درجه سلسیوس، زمان پخت: 30،60 و 90 دقیقه و با مصرف مواد شیمیایی(سولفیت سدیم16، 18و 20% ،فرمالدهید4 و6%) بر پایه وزن ماده خشک مصرفی بوده است. به منظور بررسی اثرگذاری فرمالدهید چهار تیمار مختلف در محدوده عدد کاپای 12-14 گزینش شدند. از هر نوع خمیر، کاغذ دست ساز 60 گرمی تهیه شد و ویژگی های مقاومتی آنها با استفاده از استاندارد TAPPIاندازه گیری شد. نتایج آزمایش‌ها نشان داد که استفاده از فرمالدهید در مایع پخت سولفیت علاوه بر ماده فعال CH2OHSO3- معادل 2 واحد هیدروکسید سدیم آزاد می‌کند. یون هیدروکسیل که باز بسیار قوی می‌باشد، به طور قابل توجهی لیگنین‌زدایی را آسان کرده و یون‌ CH2OHSO3- به دست آمده نیز در واکنش با لیگنین با سولفون‌دار کردن واحد‌های لیگنین سبب تسهیل در لیگنین‌زدایی و بهبود گزینش پذیری در لیگنین‌زدایی، بازده خمیرکاغذ در عدد کاپای همانندو همچنین بهبود ویژگی های مکانیکی خمیرکاغذ می‌شود.}, keywords_fa = {کاه برنج,خمیرکاغذ,سولفیت سدیم,فرمالدهید,ویژگی های مقاومتی کاغذ}, url = {https://www.ijwp.ir/article_11473.html}, eprint = {https://www.ijwp.ir/article_11473_810e6d387c83e213f2a81008f8fc622a.pdf} } @article { author = {Kamrani, Saeid and Moradifar, Alireza and Yadoollahi, Soghra and Seraian, A.Reza}, title = {The Investigation on Feasibility of Oriented Strand Boards to Parquet Production from Mixed Residual Veneer Popular and Beech}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {3}, number = {2}, pages = {25-38}, year = {2013}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {The objective of this study was to investigate of feasibility of using residual veneer (popular and beech)to manufacture oriented strand board (OSB) parquet. Percentage of mixed residual veneer popular to beech was 40%to 60% respectly. In this study press time (6, 8 and 10 min) and press temperature (170º, 180º)were selected as variables, other factors being kept constant. Results indicated that increase of press temperature had no significant effect on modules of rupture, modules of elasticity and hardness but had significant effect on internal bonding, water absorption and thickness swelling. However results indicated that increase of press time had significant effect on total physical and mechanical properties of boards.  }, keywords = {: Popular and Beech veneer residuals -oriented strand board-press time-press temperature -parquet}, title_fa = {بررسی امکان ساخت تخته تراشه جهت دار با کاربرد کفپوش از پسماندهای روکش راش و صنوبر}, abstract_fa = {هدف از این بررسی امکان سنجی استفاده از پسماندهای روکش صنوبرو راش برای تولید کفپوش از تخته تراشه جهت دار می باشد. میزان اختلاط روکش صنوبر وراش به ترتیب 60 به 40 درصد بود. در این بررسی زمان پرس (6، 8 و 10 دقیقه) و دمای پرس 170 و 180 درجه سلسیوس به عنوان عامل های متغیر و دیگر عامل ها به عنوان عامل های ثابت در نظر گرفته شد. نتایج نشان داد که افزایش دمای پرس اثرگذاری معنی دار بر مقاومت خمشی، مدول کشسانی و همچنین سختی ندارد، اما افزایش این عامل اثرگذاری معنی داری بر چسبندگی درونی، واکشیدگی ضخامت و جذب آب تخته ها دارد. همچنین برابر نتایج این تحقیق اثر افزایش زمان پرس بر همه ویژگی های فیزیکی و مکانیکی تخته تاثیر معنی دار از خود نشان داد}, keywords_fa = {پسماندهای روکش صنوبرو راش,تخته تراشه جهت دار,زمان پرس,دمای پرس,کفپوش}, url = {https://www.ijwp.ir/article_11474.html}, eprint = {https://www.ijwp.ir/article_11474_0b6c29409831e23f30f7fb5bef4f872b.pdf} } @article { author = {Faezipour, M.Mahdi and Naghizadeh, Zahra and Ebrahimi, Ghanbar and Hamzeh, Yahya}, title = {Investigation on Effect of Additives on Thermal Conductivity of Herbaceous Fiber Reinforced Cement Composite}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {3}, number = {2}, pages = {39-52}, year = {2013}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {In this research, fiber reinforcement cement composites (A and B) with low thermal conductivity were produced. Composites type B were produced by two levels of fibers (Equisetum telmateia), 15 and 25%, three levels of silica fume gel, 0, 7 and 10% and three levels of fly ash, 0, 20 and 30%. In composites type A fly ash was replaced by aluminium powder in three levels, 0, 0.08 and 0.1% (all percentage by weight) to manufacture composites with target density and thickness of 1.10 g/cm3 and 13 mm respectively. Results of tests to determine effects of additives on thermal conductivity of mentioned composites have shown that the increasing amount of each of the mentioned additives would significantly affect thermal conductivity of the experimental composites. Least thermal conductivity coefficient was observed 0.14 W/mK in composites type A, consisting 25% fiber, 10% silica fume gel and 0.1% aluminium powder. In composites type A with increasing the aluminium powder to 0.1%, silica fume gel to 10% and fiber to 25%, the thermal conductivity reduced 36, 34.78 and 42.86 % respectively. Least thermal conductivity coefficient was measured 0.17 W/mK in type B composites containing 25% fiber, 10% silica fume gel and 30% fly ash. In composites type B with increasing the amount of fly ash to 30%, silica fume gel to 10% and fiber to 25%, the thermal conductivity did decease in order of 39.18, 37.5 and 47.62%. }, keywords = {: Fiber cement composite,Silica fume gel,Aluminium powder,Equisetum telmateia,Fly ash,Thermal conductivity}, title_fa = {بررسی تاثیر مواد افزودنی بر هدایت گرمایی چندسازه سیمان- الیاف گیاهی}, abstract_fa = {در این پژوهش چندسازه‌های الیاف – سیمان نوع A و B با هدایت گرمایی کم تولید شد. چند‌سازه‌ها‌ی نوع B از 15 و 25 درصد الیاف گیاه دم‌اسبی (Equisetum telmateia)، صفر، 7 و 10 درصد ژل میکروسیلیس و صفر، 20 و 30 درصد خاکستر سبک، ساخته شدند. در چندسازه‌های نوع A به جای خاکستر سبک، صفر، 08/0 و 1/0 درصد میکرو پودر آلومینیوم (همه بر پایه جرم خشک سیمان)، برای تولید چندسازه‌هایی با چگالی و ضخامت  اسمی g/cm³ 1/1 و mm 13 مورد استفاده قرار گرفت. نتایج به دست آمده از بررسی تاثیر این مواد بر هدایت گرمایی چند سازه‌های یاد شده نشان داد که افزایش میزان هر کدام از آن‌ها اثر معنی‌داری بر کاهش هدایت گرمایی چندسازه‌های تولید شده داشته است. کم‌ترین ضریب هدایت گرمایی در چندسازه‌ها‌ی A مربوط به چندسازه‌ی ساخته شده از 25 درصد الیاف، 10 درصد ژل میکروسیلیس و 1/0 درصد پودر آلومینیوم بود که برابر W/mK 14/0 تعیین شد. در چندسازه‌های نوع A‌ با افزایش پودر آلومینیوم تا 1/0 درصد، ژل میکروسیلیس تا 10 درصد و 25- 15درصد الیاف، هدایت گرمایی به ترتیب در حدود 36، 78/34 و 86/42 درصد کاهش یافت. کمترین ضریب هدایت گرمایی در مورد چندسازه‌های نوع B معادل W/mK 17/0 و مربوط به چندسازه‌ی دارای 25 درصد الیاف، 10 درصد ژل میکروسیلیس و 30 درصد خاکستر سبک تعیین شد. در چندسازه‌های نوع B با افزایش خاکستر سبک  تا 30 درصد، ژل میکروسیلیس تا 10 درصد و 25- 15 درصد الیاف، هدایت گرمایی به ترتیب در حدود 18/39، 5/37 و 62/47 درصد کاهش نشان داد.}, keywords_fa = {چندسازه الیاف سیمان,ژل میکروسیلیس,پودر آلومینیوم,گیاه دم اسبی,خاکستر سبک,هدایت گرمایی}, url = {https://www.ijwp.ir/article_11476.html}, eprint = {https://www.ijwp.ir/article_11476_023455374d90b3b8693867e57ece66dd.pdf} } @article { author = {Hemmat abadi, Hojjat and Behrooz, Rabi}, title = {Investigation of Electro coagulation Process on TSS and COD Removal from Effluent of the Paper Recycling Mill Using Al Electrodes}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {3}, number = {2}, pages = {53-64}, year = {2013}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {Theaim of this research was investigation on the performance of an electrocoagulation process with aluminum sacrificial anode for removal of TSS and COD from effluent of a paper recycling mill. The effect of electrolysis time (10, 20, 30 and 60 min), initial electrolyte pH (3, 5, 7.5 and 10), and voltage (9 and 12V) were studied on the electrocoagulation efficiency. Increase of voltage from 9 to 12 V caused significantly removal of TSS and COD whichthe highest removal rate at 12 voltages for TSS and COD were 99%, and 77%, respectively, while the values for the same parameters at voltage 9 were 97% and 33%. The results also show that the initial pH of effluent has a key role in process efficiency so that in neutral limit the TSS and COD removal was more than the other pHs. It can be concluded that EC technique can be used as a simple and efficient method for treatment of paper recycling mill effluent and thereby pollution reduction.}, keywords = {electrocoagulation,Paper recycling,Effluent,TSS,COD}, title_fa = {بررسی قابلیت استفاده از فرایند الکتروکواگولاسیون با استفاده از الکترودهای آلومینیوم در کاهش TSS و COD پساب کارخانه بازیافت کاغذ}, abstract_fa = {هدف از این بررسی ارزیابی بازده کاهش TSS وCODاز پساب صنعتی بازیافت کاغذ توسط فرایند الکتروشیمیایی با استفاده از الکترود آلومینیوم است. عامل های زمان الکترولیز (10، 20، 30 و 60 دقیقه)، pHنخستین پساب (3، 5، 5/7 و10) و ولتاژ (9 و 12ولت) روی بازده فرایند الکتروکواگولاسیون برای تیمار این پساب مورد بررسی قرار گرفت. افزایش زمان الکترولیز سبب کاهشTSS و COD پساب شد. افزایش ولتاژ از 9 به 12 ولت به طور چشمگیری سبب کاهش TSS و COD پساب شد به طوری که میزان کاهش در ولتاژ 12 برای TSSو COD به ترتیب 99 و 77 درصد بودند اما این میزان کاهش در ولتاژ 9 به ترتیب 97 و33 درصد بودند. همچنین نتایج نشان داد که pHنخستین پساب نقش مهمی را در کارآیی فرایند ایفا می‌کند به گونه ای که در محدوده pH خنثی میزان TSS و COD کاهش بیشتری را در فرایند نشان داد. نتایج این تحقیق نشان داد که روش الکتروکواگولاسیون می‌تواند به عنوان یک روش ساده و موثر برای تیمار پساب کارخانه های بازیافت کاغذ و کاهش آلودگی از آنها مورد استفاده قرار گیرد.}, keywords_fa = {الکتروکواگولاسیون,پساب,صنایع بازیافت کاغذ,TSS,.COD}, url = {https://www.ijwp.ir/article_11479.html}, eprint = {https://www.ijwp.ir/article_11479_4cd0f629b6ed790d303fd4a0213a3d1a.pdf} } @article { author = {Kord, Behzad and Najafi, Abdollah and Rezvani, Mohammad}, title = {Investigation on the Effect of Penetration Depth and Installing Method of Screw on Withdrawal Resistance in Face and Edge of Wood Plastic Composite}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {3}, number = {2}, pages = {65-75}, year = {2013}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {In this study, the effects of penetration depth and the installing method of screw (with drill and without drill) on withdrawal resistance in face and edge of wood plastic panel were investigated. To meet this objective, the wood plastic panels from the malach choob factory with density of 1.017gr/cm3 and 100×100×1.4 cm3 indimension were prepared, and for withdrawal resistance test the screw with 3 mm in diameter and 2.5 mm in length were used. Then, the samples with dimension of 2×6×1.6 cm3 according to Iranian national standard (No: 7416) were selected and the screw joint in face and edge of panels according to variables including penetration depth of screw (6, 9 and 12 mm) and penetration type of screw (with drill and without drill) was done and the withdrawal resistance were measured on the samples. The results indicated that the withdrawal resistance of screw in wood plastic panels increases with increase of penetration depth of screw from 6 to 12 mm. Also, because of fibre compression and high density, the face of panels had higher withdrawal resistance of screw as compared with edge of them. With drilling the withdrawal resistance of screw in wood plastic panels were increased.}, keywords = {: Withdrawal resistance of screw,penetration depth,Installing method face and edge of panel,wood plastic composite}, title_fa = {بررسی تاثیر عمق نفوذ و روش نصب پیچ بر توان نگه‌داری پیچ در سطح و لبه چندسازه چوب پلاستیک}, abstract_fa = {در این تحقیق تأثیر عمق نفوذ و روش نصب پیچ (با سوراخ پیش‌ساخته و بدون سوراخ) بر توان نگهداری پیچ در سطح و لبه چندسازه چوب پلاستیک انجام شد. به این منظور تخته‌های چوب پلاستیک از کارخانه ملج چوب گرگان با چگالی 017/1 گرم بر سانتی‌متر مکعب و ابعاد 4/1×100×100 سانتی‌متر مکعب تهیه شده و برای انجام آزمون از پیچ خودکار شماره 6 با قطر 3 میلی متر و طول 5/2 سانتی‌متر استفاده شد. آنگاه ابعاد نمونه‌های آزمونی با توجه به استاندارد ملی ایران به شماره 7416، 6/1×6×2 سانتی‌متر مکعب تعیین شد، و به منظور اتصال پیچ در سطح و لبه تخته‌‌ها سوراخی بسته به عمق نفوذ پیچ (6، 9 و 12 میلی‌متر) و روش نصب پیچ (با سوراخ پیش‌ساخته و بدون سوراخ) تعبیه شده و نمونه‌ها تحت آزمون  توان نگهداری پیچ  قرار گرفتند. نتایج نشان داد که با افزایش عمق نفوذ پیچ از 6 به 12 میلی‌متر، توان نگهداری پیچ افزایش می‌یابد. همچنین سطح تخته نسبت به لبه آن به علت فشردگی الیاف و چگالی بالاتر توان نگهداری پیچ بیشتری را دارد. همچنین مشخص شد با ایجاد سوراخ پیش‌ساخته، توان نگهداری پیچ در چندسازه چوب پلاستیک نسبت به بدون سوراخ  بیشتر می‌باشد}, keywords_fa = {توان نگهداری پیچ,عمق نفوذ,روش نصب,سطح و لبه تخته,چندسازه چوب پلاستیک}, url = {https://www.ijwp.ir/article_11481.html}, eprint = {https://www.ijwp.ir/article_11481_f626bf7b1490547e273073a6283354e4.pdf} } @article { author = {Alinia, Sahba and Afra, Elyas and Resalati, Hossein and Yousefi, Hossein}, title = {Effect of Mixing Temperature of CMP Pulp and Cellulose Nanofiber on Paper Properties}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {3}, number = {2}, pages = {77-90}, year = {2013}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {Several processing parameters affect the function of cellulose nanofiber as an environmentally friend cellulosic reinforcer. One of the potential parameters can be the mixing temperature of pulp and cellulose nanofiber that has been investigated in this study. In order to study the influence of this parameter, mixing drainage velocity and the air permeability and strength properties of resulting paper were measured. A mixture of chemi-mechanical pulp suspensions (with concentration of 0.2 wt% and freeness of 250 ml, CSF) containing 5 wt% cellulose nanofiber were prepared. This mixture was then stirred at 25, 50, and 70 ◦C using a magnetic stirrer for 1 hour followed by draining using vacuum filtration to make wet handsheet. The wet handsheet was first pressed, and then dried in oven at 100 ◦C for 24 hours. The test’ results showed that the increase of mixing temperature led to decreasing drainage time and air permeability. The strength properties of paper reinforced by nanofibers were positively affected by mixing temperature (i.e. the more mixing temperature, the higher strength). The data of tensile strength index was considerably increased. The tear strength of paper increased approximately by 200% over rising mixing temperature.  }, keywords = {Cellulose nanofiber,Mixing temperature,Chemi-mechanical pulp and Physical and strength properties of paper}, title_fa = {ارزیابی تاثیر دمای اختلاط خمیرکاغذ شیمیایی مکانیکی و نانوفیبر سلولز بر ویژگی‌های کاغذ}, abstract_fa = {عامل های فرآیندی بسیاری بر چگونگی عملکرد نانوفیبر سلولز به عنوان یک تقویت‌کنندۀ سلولزی دوست‌دار محیط زیست تأثیرگذارند. یکی از عامل های بالقوه تأثیرگذار، دمای اختلاط سوسپانسیون خمیر با نانوفیبر سلولز بوده که در این تحقیق به آن پرداخته شده است. به منظور بررسی تأثیر این مشخصه شتاب آبگیری اختلاط به دست آمده و ویژگی های مقاومتی کاغذ نهایی تولیدشده مورد آزمون و بررسی قرار گرفت. بدین منظور سوسپانسیون‌های (غلظت 2/0%) با 5% وزنی نانوفیبر سلولز و خمیر شیمیایی‌مکانیکی با درجۀ روانیml, CSF250 تهیه و پس از اختلاط بر روی همزن مغناطیسی به مدت ‌1ساعت و در دمای 25، 50 و◦C70 همزنی شدند. سوسپانسیون به دست آمده با پالایش (فیلتراسیون) خلاء آبگیری شد. پس از آبگیری، کاغذ تولیدی پرس و در آون به مدت 24ساعت در دمای ◦C100 خشک شد. نتایج آزمایش‌ها نشان دادند که افزایش دمای اختلاط موجب کاهش زمان آبگیری، بهبود ویژگی‌های مقاومتی و کاهش میزان نفوذپذیری ‌به ‌هوای کاغذ نهایی شدند. میزان شاخص مقاومت کششی افزایش چشم‌گیری داشته و با افزایش دما تا◦C70، مقاومت به‌ پارگی کاغذ در حدود دو برابر افزایش یافت.}, keywords_fa = {نانوفیبر سلولز,دمای اختلاط,خمیر شیمیایی‌مکانیکی,ویژگی های فیزیکی,مقاومت کاغذ}, url = {https://www.ijwp.ir/article_11484.html}, eprint = {https://www.ijwp.ir/article_11484_4feeb97ea552aec9392aa022afbf2d7e.pdf} } @article { author = {Zeyni, Farhad and Dehghani, M.Reza}, title = {A Comparison Between Alkali Peroxide and Activated Peroxide Processes in Bleaching Hardwoods Chemi-mechanical Pulp}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {3}, number = {2}, pages = {91-103}, year = {2013}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {Unbleached chemi-mechanical pulp of 85% pulp yield and produced from hornbeam, beech and populus woods respectively by 3:1:1 ratio, was used for peroxide bleaching. Two bleaching systems, alkali peroxide (conventional bleaching) and activated peroxide by TAED activator, were used for pulp bleaching. Bleaching treatments included different percentages of hydrogen peroxide and caustic soda consumption. In this research, the hydrogen peroxide consumption rate, pulp yield, process selectivity, bleached pulp brightness and bleaching effluent pollution load (COD) were investigated. Results showed that, brightness values were increased by bleach chemicals charge rising, in both bleaching systems, but the increasing trend was downward. Also, pulp yield was decreased by increase of chemical charges, but residual peroxide was raised. The activated peroxide process compare to conventional process had lower efficiency and brightness improvement values of pulp were less than those of alkali peroxide process. But pulp yield and effluent pollution load was less by activated peroxide bleaching.}, keywords = {Alkali peroxide,Activated peroxide,brightness,Effluent pollution load,TAED}, title_fa = {ارزیابی فرایند پراکسید قلیایی و پراکسید فعال‌شده در رنگ‌بری خمیرکاغذ شیمیایی- مکانیکی حاصل از چوب پهن‌برگان}, abstract_fa = {خمیرکاغذ شیمیایی‌مکانیکی (CMP) رنگ‌بری نشده، دارای بازده خمیرسازی 85% و تولید شده از گونه‌های ممرز، راش و صنوبر به‌ترتیب با نسبت 3، 1 و 1، برای رنگ‌بری با پراکسید مورد استفاده قرار گرفت. برای رنگ‌بری خمیرکاغذ از دو سامانه پراکسید قلیایی (رنگ‌بری متداول) و پراکسید فعال‌شده توسط ماده فعال‌ساز TAED، استفاده شد. تیمارهای مورد استفاده برای رنگ‌بری شامل درصدهای مختلف پراکسید هیدروژن و سود سوزآور بود. ویژگی‌های مورد ارزیابی در این تحقیق، میزان کاربری پراکسید هیدروژن، بازده رنگ‌بری، گزینندگی فرایند، روشنی خمیرکاغذ رنگ‌بری‌شده و میزان بار آلودگی (COD) پسآب تولید شده از رنگ‌بری بود. نتایج به دست آمده نشان داد که در هر دو سامانه رنگ‌بری، با افزایش کاربری مواد شیمیایی رنگ‌زدا، میزان روشنی افزایش می‌یابد، اما روند این افزایش دارای سیر کاهشی بود. با افزایش کاربری مواد شیمیایی رنگ‌زدا، بازده رنگ‌بری کاهش یافته اما میزان پراکسید باقی‌مانده افزایش می‌یابد. مقایسه فرایند پراکسید فعال‌شده با فرایند متداول نشان داد که، کارایی رنگ‌بری پراکسید فعال‌شده کمتر بود و میزان بهبود روشنی خمیرکاغذ نسبت به فرایند رنگ‌بری پراکسید قلیایی افت پیدا کرد. اما میزان بازده و همچنین بار آلودگی پسآب در سامانه رنگ‌بری پراکسید فعال‌شده کمتر بود.  }, keywords_fa = {پراکسید قلیایی,پراکسید فعال‌شده,روشنی,بار آلودگی پسآب,TAED}, url = {https://www.ijwp.ir/article_11487.html}, eprint = {https://www.ijwp.ir/article_11487_7fc86be7e6005c799177e3c6de6091ee.pdf} } @article { author = {Darstan, Rasoul and Zabihzadeh, Majid and Nazarnezhad, Noorodin}, title = {Papermaking Properties of Carpinus betulus with kraft, Soda and Soda-Urea Pulping Processes}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {3}, number = {2}, pages = {105-117}, year = {2013}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {This research was carried out in order to comparatively investigate the hornbeam kraft, soda and soda-urea papermaking properties. The selected treatment in kraft process had an average yield of 44.43% and kappa number of 23.75. In soda process the selected treatment had an average yield of 38.75% and kappa number of 19.28. In soda-urea process, the selected treatments had an average yield of 39.85, 40.1, 40.5, 39.8 and 40.61 and kappa number of 21.21, 22.33, 22.66, 25.28 and 26.85. After refining the selected pulp to reach the freeness of 400±25 ml CSF, 60 g/m2 handsheets were made and physical, mechanical and optical properties were measured. Results showed that kraft pulps had higher yield and better refinability than soda and soda-urea pulps. Papers made from kraft process had higher strength properties than those made of soda and soda-urea process. With addition of urea, yield and kappa number of pulps increased. The highest improvement in tensile index, breaking length and tear index was achieved with addition of 3% urea and the highest improvement in burst index was achieved with adding 4% urea. Results of brightness measurements showed that papers from kraft and soda processes had the lowest and highest brightness degree respectively. With the addition of urea, brightness of papers decreased.}, keywords = {Carpinus betulus,Kraft,soda,Soda- urea,Mechanical properties,brightness}, title_fa = {ارزیابی ویژگی‌های کاغذسازی گونه ممرز با فرآیندهای کرافت، سودا و سودا- اوره}, abstract_fa = {این تحقیق با هدف بررسی مقایسه‌ای کاغذ ساخته شده از گونه ممرز با فرآیندهای سودا، سودا- اوره و کرافت و ارزیابی ویژگی‌های کاغذسازی آن‌ها انجام شد. تیمار گزینش شده در فرآیند کرافت دارای بازده 43/44 درصد و عدد کاپای 75/23، در فرآیند سودا دارای بازده 75/38 درصد و عدد کاپای 28/19 و در فرآیند سودا- اوره دارای بازده 85/39، 1/40، 5/40، 8/39، 61/40 درصد و عدد کاپای 21/21، 33/22، 66/22، 28/25 و 85/26 بودند. پس از پالایش و رسیدن به درجه روانی  ml CSF 25±400 برای هر یک از تیمارهای گزینش شده، کاغذ دست ساز با جرم پایه 60 گرم بر متر مربع ساخته شد و ویژگی‌های فیزیکی، مقاومتی و نوری آنها ارزیابی شد. نتایج نشان داد که خمیرکاغذهای ساخته شده از فرآیند کرافت بازده بیشتر و پالایش پذیری بهتری در مقایسه با خمیرکاغذهای ساخته شده از فرآیندهای سودا و سودا- اوره دارند. کاغذهای ساخته شده با فرآیند کرافت نیز دارای ویژگی‌های مقاومتی بالاتری نسبت به فرآیندهای سودا و سودا- اوره هستند. با افزودن اوره، بازده و عدد کاپای خمیرکاغذها افزایش یافت. بیشترین بهبود در شاخص مقاومت در برابر کشش، طول پاره شدن و شاخص مقاومت در برابر پاره شدن با افزودن 3 درصد اوره و بیشترین بهبود در شاخص مقاومت در برابر ترکیدن با افزودن 4 درصد اوره به دست آمد. نتایج اندازه گیری درجه روشنی نشان داد که کاغذهای ساخته شده از فرآیند کرافت و سودا به ترتیب دارای کمترین و بیشترین درجه روشنی هستند. با افزودن اوره درجه روشنی کاغذها نیز کاهش یافت. }, keywords_fa = {ممرز,کرافت,سودا,سودا- اوره,ویژگی های مکانیکی,درجه روشنی}, url = {https://www.ijwp.ir/article_11488.html}, eprint = {https://www.ijwp.ir/article_11488_ee6347090494eaacf58b1795d8d0e7ee.pdf} } @article { author = {Darabi, Peyvand and Karimi, A.Naghi and Azadfallah, Mohammad and Tajvidi, Mahdi}, title = {Properties Evaluation of High Density Polyethylene Composite Filled with Bagasse after Accelerated Weathered}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {3}, number = {2}, pages = {119-130}, year = {2013}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {Wood plastic composites (WPCs) are produced from a mixture of wood (in different sizes) and resin (thermoset or thermoplastic). This product has many applications as structural and non-structural materials and since its emerge in market its use received an increasing trend. Adding wood flour to polymer not only improves its mechanical properties compared to net polymer, but also leads to products with moldability characteristics. With increasing demand of WPCs and reduction in forest harvest according to new protecting law of forestry, and lack of raw materials for producers, other lignocelluloses materials replace wood flour. Agricultural by-products such as hemp, coir, rice husk and bagasse (residual from sugar cane extraction) are the examples that can be used in WPCs. As the outdoor application of Wood Plastic Composites (WPCs) becomes more widespread, the resistance of its products against weathering, particularly ultraviolet (UV) light becomes more concerned. When WPCs are exposed to outdoor, ultraviolet (UV) light, rain, snow and atmospheric pollution, they will be degraded which is marked by color fade and loss in mechanical properties. Nowadays many manufactures of WPCs use bagasse as a raw material. Their production in different color and shapes are used as arbors and pergolas and also as decorative applications for outdoor uses. However, so far there has been no research done on the effects of weathering on composites made from bagasse. In present study, composites from bagasse and high density polyethylene, with and without pigments in master batch, have been made through extrusion. Then samples were exposed to accelerated weathering for 1440h. After this period of time samples were removed and their chemical, mechanical and surface qualities were studied. The results have shown that using bagasse as filler can relatively reduce the discoloration of weathered samples. Moreover, adding pigments to WPCs can increase colorstability, while it would cause higher loss in mechanical properties.}, keywords = {Weathering,wood plastic composite,Discoloration,Bagasse,FTIR spectroscopy,Mechanical properties}, title_fa = {ارزیابی ویژگی های چندسازه‌های چوب پلاستیک ساخته شده از باگاس بعد از هوادیدگی تسریع شده}, abstract_fa = {چندسازه چوب پلاستیک (WPCs) ماده مرکبی متشکل از مخلوط چوب ( به صورت آرد یا ذره های لیفی) و رزین (ترموست یا ترموپلاستیک) می‌باشد. این محصول در مصارف ساختمانی و غیر ساختمانی کاربرد بسیار دارد و از سال پیدایش تا کنون مصرف آن روندی رو به رشد داشته است. افزودن آرد چوب درون پلیمر نه تنها باعث بهبود خواص مکانیکی این محصول در مقایسه با پلیمر خالص می‌شود، بلکه ویژگی شکل‌پذیری این محصول منجر به افزایش کاربرد آن نیز می‌شود. با افزایش تقاضا برای این محصول، کاهش برداشت از جنگل‌ها در پی قوانین حفاظت از جنگل‌ها و رو به رو شدن تولید کنندگان این صنعت با کمبود ماده اولیه، دیگر مواد لیگنوسلولزی به عنوان جایگزین برای آرد چوب مورد استفاده قرار گرفتند. فرآورده‌های جانبی محصولات کشاورزی مانند کنف، لیف نارگیل، سبوس برنج و باگاس (پسماند نیشکر پس از استخراج شکر) از جمله مواد لیگنوسلولزی هستند که در ساخت این محصول می‌توان از آنها به عنوان پرکننده پلیمر استفاده کرد.افزایش مصارف چندسازه چوب پلاستیک (WPC)در محیط بیرون از ساختمان بیش از پیش اهمیت دوام این فراورده را روشن می‌سازد. این محصولات هنگامی که به مدت طولانی در معرض اشعه فرابنفش (فرسایش نوری)، باران، برف و آلودگی‌های جوی بیرون از ساختمان قرار می‌گیرند، دچار تخریب می‌شوند که تغییر رنگ و کاهش ویژگی های مکانیکی از مشخصه‌های این گونه تخریب می‌باشند. امروزه بسیاری از کارخانه های تولیدی چوب پلاستیک از باگاس به عنوان ماده اولیه استفاده می‌کنند. محصولات این کارخانه ها در مصارفی چون آلاچیق سازی، رونمای ساختمان و غیره، در رنگ‌ها و طرح‌های مختلف مورد استفاده قرار می‌گیرد. لیکن تا کنون تحقیقی در رابطه با میزان تاثیر هوازدگی بر روی ویژگی های این سازه ساخته شده از باگاس صورت نگرفته است. در این تحقیق نمونه‌های پلی اتیلن با چگالی بالا همراه با مخلوط باگاس به صورت رنگی و غیر رنگی،  توسط دستگاه تزریق چسب (اکسترود) به صورت نما رخ (پروفیل) ساخته و به مدت 1440 ساعت تحت تاثیر هوازدگی تسریع شده قرار گرفتند. شدت تغییر و نوسان شیمیایی و مکانیک و کیفیت سطح نمونه‌ها پس از هوازدگی مورد بررسی قرار گرفت. نتایج نشان داد استفاده از باگاس به عنوان پرکننده در پلی‌اتیلن با چگالی بالا می‌تواند تغییر رنگ ناشی از هوازدگی را در مقایسه با محصولات دیگر ساخته شده از آرد چوب کاهش دهد. استفاده از رنگدانه درون ترکیبات چندسازه چوب پلاستیک می‌تواند در برابر هوادیدگی ثبات رنگی را افزایش دهد، هر چند تاثیر مثبتی بر روی ویژگی های مکانیکی نداشته‌اند.}, keywords_fa = {هوازدگی,چندسازه چوب پلاستیک,تغییر رنگ,باگاس و ویژگی های مکانیکی}, url = {https://www.ijwp.ir/article_11489.html}, eprint = {https://www.ijwp.ir/article_11489_f40ec820aebe3b7e013e3d28cb487460.pdf} } @article { author = {Kargarfard, Abolfazl}, title = {The Infuence of Coupling Agent and the Content of Fibers on Tensile Strength and Physical Properties of Cotton Fiber Stem/Recycled Polypropylene Composites}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {3}, number = {2}, pages = {131-140}, year = {2013}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {The objective of this study was to investigate the influence of coupling agent and the content of fiber on tensile strength and physical properties of wood/plastic composite produced from recycled polypropylene using mat forming procedure. Recycled polypropylene and three levels of Cotton Fiber Stem (50, 55 and 60%) and three levels of MAPP (0, 3 and 5%) were used. The results of tensile strength and physical properties were statistically analyzed using factorial experimental design. The results indicated that the tensile strength of composites with increasing MAPP content and decreasing of fiber content was improved However the modulus of tensile reduced significantly when the fibers content reduced. Also, the physical properties of composites were improved with increasing of MAPP consumption. Thickness swelling of composites after 24 hours and water absorption after 2 hours in boiling water showed these properties are lower when 50% fibers is used. }, keywords = {wood plastic composite,Recycled polypropylene,coupling agent,Cotton fiber stem,Tensile strength and physical properties}, title_fa = {بررسی و ارزیابی تاثیر میزان سازگارکننده و الیاف بر ویژگی های کششی و فیزیکی چند سازه لیاف ساقه پنبه- پلی پروپیلن بازیافت شده}, abstract_fa = {هدف این بررسی، استفاده از الیاف ساقه پنبه و پلی پروپیلن بازیافتی در تولید چند سازه های چوب/ پلاستیک به روش ریزش کیک بوده است. لذا از الیاف ساقه پنبه در 3 سطح 50، 55 و 60 درصد (بر پایه وزن خشک چند سازه) و همچنین استفاده از 3 سطح ماده جفت کننده MAPP[1] ( صفر، 3 و 5 درصد) با استفاده از پروپیلن بازیافتی چند سازه های چوب- پلاستیک ساخته شد. نتایج اندازه گیری ویژگیهای کششی و فیزیکی چند سازه ها با استفاده از طرح آزمایش فاکتوریل در قالب طرح کامل تصادفی تجزیه و تحلیل شدند. نتایج نشان داد که مقاومت کششی چند سازه های ساخته شده با افزایش میزان سازگارکننده و کاهش مصرف الیاف بهبود یافته است. در حالی که مدول کشسانی کششی با کاهش میزان الیاف به طور معنی داری کاهش یافت. همچنین همه ویژگیهای فیزیکی چندسازه ها با افزایش مصرف سازگارکننده بهبود یافتند. همچنین با کاهش میزان الیاف، واکشیدگی ضخامت 24 ساعت و جذب آب 2 ساعت در آب جوش به کمترین میزان کاهش یافتند.   1}, keywords_fa = {چند سازه چوب/پلاستیک,پلی پروپیلن بازیافتی,الیاف ساقه پنبه,ویژگیهای کششی,ویژگیهای فیزیکی}, url = {https://www.ijwp.ir/article_11490.html}, eprint = {https://www.ijwp.ir/article_11490_f7218768ae02c0d0f3c699d34c4f487d.pdf} } @article { author = {Pirayeshfar, Amir hossein and Jalili, M.Mahdi and Musavi, Yahya}, title = {A Study on Tensile Behavior and Water Uptake of Wood Powder-Composites Based on Epoxy and Unsaturated Polyester Resins}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {3}, number = {2}, pages = {141-156}, year = {2013}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {In this study, two kinds of epoxy resins (i.e. high-viscosity and low-viscosity) as well as one polyester resin (orthophthalic grade) were selected and examined as pure resins and also as a polymeric matrix for producing wood-composites. In this study, tensile properties, water uptake, and degradation of samples in water were also investigated. The results show that addition of wood particles to the thermoset resins strongly impresses on their tensile behavior and water uptake. Tensile studies show that addition of wood powder improves the tensile properties of polyester resin as compared with viscosity epoxy one, although its modulus value is relatively less than that of low viscosity epoxy resin. Water uptake measurements also revealed that pure polyester resin and its related composites possess minimum water uptake and less degradation in water as compared with corresponding epoxy specimens and from which the lowest extent of materials is extracted and migrated to the water even after 50 days immersion in water.  }, keywords = {Epoxy resin,Unsaturated polyester resin,Wood powder-composite,Tensile,Water uptake,Extracted materials}, title_fa = {بررسی و ارزیابی رفتار کششی و جذب آب چند سازه‌های چوب/ اپوکسی و چوب/ پلی‌استر}, abstract_fa = {در این پژوهش، دو نوع رزین اپوکسی با غلظت (ویسکوزیته) بالا و پایین و یک نوع رزین پلی‌استر غیر اشباع گزینش شد و برای تولید نمونه‌های رزین خالص و همچنین چندسازه مورد استفاده قرار گرفتند. در این بررسی ویژگی های کششی، جذب آب و میزان شدت تخریب نمونه‌ها در آب مورد بررسی قرار گرفت. نتایج به دست آمده نشان داد که اضافه کردن پودر چوب به رزین‌های یاد شده تاثیر قابل ملاحظه‌ای بر ویژگی های کششی و جذب آب آنها دارد. آزمون کشش نشان داد که اگرچه مدول رزین پلی‌استر خالص تا حدودی پایین‌تر از رزین اپوکسی با غلظت کم بود، ولی به هر حال پس از اضافه شدن پودر چوب، ویژگی های کششی چندسازه پلی استر در مقایسه با چندسازه اپوکسی با غلظت کم بهینه تر گزارش شد. بررسی میزان جذب آب نشان داد که رزین پلی‌استر خالص و چندسازه ساخته شده از آن کمترین میزان جذب آب را در مقایسه با نمونه‌های همانند رزین اپوکسی دارند، به علاوه میزان تخریب نمونه پلی‌استر خالص و چندسازه‌های ساخته شده از آن در مقایسه با نمونه‌های همانند از رزین اپوکسی پایین‌تر بود، به طوری که پس از گذشت 50 روز غوطه‌وری در آب، کمترین میزان مواد استخراجی از چندسازه‌های پلی‌استری به درون آب وارد شده بود.}, keywords_fa = {رزین اپوکسی,رزین پلی‌استر غیر اشباع,چندسازه,ویژگی های کشش,جذب آب}, url = {https://www.ijwp.ir/article_11491.html}, eprint = {https://www.ijwp.ir/article_11491_22e7e19ad264893cad19cfade3500768.pdf} } @article { author = {Moradi, Masoumeh and Kermanian, Hossein and Mousavi, Saeid and Ramezani, Omid}, title = {Effect of Lactase Enzyme on Delignification and Physical Properties of OCC Pulp}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {3}, number = {2}, pages = {157-170}, year = {2013}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {Old Corrugated Container (OCC) recycled pulp provided by a local paper manufacturing company was treated by lactase enzyme. The pulp was sampled from headbox and treated by enzyme in the conditions of consistency 2%, pH 5, reaction time 2 hours, and reaction temperature 60 °C in dosing levels of 0.005, 0.01 and 0.015 % based on oven-dried weight of pulp. Fiber classification of the control pulp showed 31.3 % of fines content and 0.82 mm average fiber length. Results have indicated that lactase treatment decreased kappa number and SR degree to 20% and 14 degrees, respectively which consequently facilitated the drainage of pulp. The extraction of treated samples showed a peak at around 280 nm, confirming the delignification of pulp by enzyme. Microscopic observation of fiber walls of the treated sample indicated a local separation of middle lamella, fiber linting and removal of fines from fiber surface. The highest Water Retention Value (WRV) was measured to be at 0.015% enzyme addition level. The apparent density of handsheets made from treated samples was lower compared with the handsheets made of control pulp resulting in loss of paper strengths.}, keywords = {Lactase enzyme,Old Corrugated Container (OCC),SR degree,kappa number,Water retention value (WRV),Apparent density}, title_fa = {بررسی و ارزیابی تاثیر آنزیم لاکاز بر میزان لیگنین‌زدایی و ویژگی‌های فیزیکی خمیرکاغذ کارتن کهنه}, abstract_fa = {در این تحقیق از آنزیم لاکاز برای تیمار خمیرکاغذ باز‌‌یافتی کارتن‌ کهنه کنگره‌ای (OCC)تهیه شده از یک واحد تولیدی کاغذ آزمایشی لاینر در داخل کشور استفاده شد. خمیرکاغذ از جعبه تغذیه کارخانه تهیه و در درصد خشکی 2، اسیدیته 5، مدت زمان 2 ساعت و دمای 60 درجه سلسیوس در سه سطح (005/0، 01/0 و 015/0 درصد بر مبنای وزن خشک خمیرکاغذ) با آنزیم لاکاز تیمار شد. طبقه‌بندی خمیرکاغذ شاهد نشان داد که 3/31% آن شامل نرمه‌ها بوده و میانگین طول الیاف 82/0 میلیمتر به دست آمد. نتایج نشان داد که تیمار با آنزیم لاکاز منجر به کاهش عدد کاپای خمیرکاغذ تا حدود 20% و همچنین کاهش درجه SR تا حدود 14 واحد و در نتیجه آسانگری در قابلیت آبگیری خمیرکاغذ شد. طیف‌سنجی عصاره استخراجی نمونه تیمار شده نیز گویای افزایش نسبی جذب در طول موج 280 نانومتر و تأیید لیگنین‌زدایی خمیرکاغذ توسط آنزیم می‌باشد. بررسی میکروسکوپی دیواره الیاف نمونه تیمار شده مؤید جدا شدن موضعی دیواره بین‌سلولی، پرز‌دار شدن و عاری بودن سطح الیاف از نرمه‌ها می‌باشد. بیشینه میزان ماندگاری آب در دیواره الیاف (WRV) با استفاده از 015/0  درصد آنزیم به دست آمد. چگالی ظاهری کاغذهای ساخته شده از الیاف تیمار شده نسبت به شاهد کاهش نشان داد که انتظار کاهش مقاومت‌های کاغذ را به دنبال خواهد داشت.  }, keywords_fa = {آنزیم لاکاز,کارتن کهنه کنگره‌ای,درجه SR,عدد کاپا,میزان ماندگاری آب,چگالی ظاهری}, url = {https://www.ijwp.ir/article_11492.html}, eprint = {https://www.ijwp.ir/article_11492_e7658a3eebd77bf21cf7795fffd82ee4.pdf} } @article { author = {Maleki, Sadegh and Dalvand, Mosayeb and Gholamian, Hadi}, title = {Determination of Screw and Nail Withdrawal Strengths in Parallel and Perpendicular to Grain of some Hardwoods of Iran}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {3}, number = {2}, pages = {171-180}, year = {2013}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {In this study, screw and nail withdrawal strengths parallel and perpendicular longitudinal to grain of some hardwoods; oak (Quercus castaneifolia), hornbeam (Carpinus betulus), beech (Fagus orientalis), Sycamore (Platanus oriantalis) and poplar (Populus deltoids) were investigated. The tests were conducted following ASTM D 1761 with specimen dimension of 15×5×5(T×R×L). Three kinds of screws namely sheet metal screw, wood screw and coarse drywall screw with diameter of 4 and 5 mm were used. Three different nails with nominal diameter of 2.5, 3.25 and 3.75 mm were also used. The highest screw withdrawal strengths parallel and perpendicular to grain were related to hornbeam, beech, oak, Sycamore and poplar respectively. Furthermore, the highest nail withdrawal strengths parallel and perpendicular to grain were related to hornbeam, oak, beech, Sycamore and poplar respectively for nails with 3.75 mm diameter. Higher density and shear strength of hornbeam compared to the other species accounts for its high screw and nail withdrawal strengths parallel and perpendicular to grain.  }, keywords = {Screw,Nail,Withdrawal resistance,Hardwood species,Longitudinal,Perpendicular}, title_fa = {بررسی و سنجش توان‌نگه‌داری پیچ و میخ در برخی از گونه‌‌های چوبی پهن برگ ایران در دو جهت موازی و عمود بر الیاف}, abstract_fa = {این پژوهش به منظور بررسی و سنجش میزان توان نگهداری پیچ و میخ در گونه‌های چوبی پهن‌برگ بلوط (Quercus castaneifolia)، ممرز (Carpinus betulus)، راش(Fagus orientalis)، چنار (Platanus oriantalis) و صنوبر(Populus deltoides) در دو جهت موازی و عمود بر الیاف انجام شده است. نمونه‌های آزمونی با پیروی از استاندارد ASTM-1761D و با ابعاد 5×5×15 (T×R×L) ساخته شدند. از سه نوع پیچ به ترتیب پیچ خودکار، پیچ پانلی رزوه درشت و پیچ چوب در اندازه‌های قطری 4 و 5 میلی‌متر و همچنین از 3 اندازه مختلف میخ به ترتیب با قطر 5/2، 25/3 و 75/3 میلی‌متر برای ساخت نمونه‌های آزمونی استفاده شد. نتایج نشان دادند که با افزایش قطر پیچ و میخ توان‌نگهداری افزایش می‌یابد. بیشترین توان‌نگهداری در جهت موازی و عمود بر الیاف به ترتیب مربوط به گونه‌های چوبی ممرز، راش، بلوط، چنار و صنوبر با پیچ چوب و بیشترین توان‌نگهداری میخ در جهت موازی و عمود بر الیاف به ترتیب مربوط به گونه‌های چوبی ممرز، بلوط، راش، چنار و صنوبر با قطر 75/3 دیده شد. دلیل بیشتر بودن توان نگهداری پیچ و میخ در اتصال های ساخته شده از چوب ممرز ناشی از جرم ویژه و نیروی برشی بیشتر این گونه نسبت گونه‌های دیگر می‌باشد.}, keywords_fa = {: پیچ,میخ,توان‌نگهداری,گونه‌های چوبی پهن‌ برگ,موازی بر الیاف,عمود بر الیاف}, url = {https://www.ijwp.ir/article_11493.html}, eprint = {https://www.ijwp.ir/article_11493_20f95f66ad1f0a49f2e87247068dc464.pdf} }